Note The Catalyst series switches Catalyst switch and Catalyst switch are described in a separate publication, the Catalyst Series Switches Installation Guide. The Catalyst switch is a 3-slot horizontal chassis supporting redundant power supplies, redundant supervisor engines, and slots for up to two modules.
Figure shows the front view of the chassis and Figure shows the rear view of the chassis. Figure Catalyst Switch—Front View. Figure Catalyst Switch—Rear View. Table lists the features of the Catalyst switch chassis.
Table Catalyst Switch Features. Note Refer to your software release notes for the minimum software release versions required to support the supervisor engines. Note Slots not occupied by supervisor engines can be used for modules. Check your software release notes for any restrictions on the type of module that can be installed. Note In systems with redundant supervisor engines, both supervisor engines must be the same model and have the same daughter card configurations.
Each supervisor engine must have the resources to run the switch on its own, which means that all supervisor engine resources are duplicated. Identical supervisor engine memory configurations are recommended, but are not required as long as the supervisor engine with the smaller memory configuration is sufficient to run the configured features of the switch.
Additionally, each supervisor engine must have its own flash device and console port connections. Note Check your software release notes for specific information. Required for Supervisor Engine 32 and Supervisor Engine Supports Supervisor Engine 2. Note Both fan tray models contain four individual fans. The individual fans are not field replaceable; you must replace the fan tray in the event of a fan failure.
The DC-input power supplies for these chassis do not have a separate ground. Systems with dual power supplies must have a minimum configuration of one fan tray, one supervisor engine, and one additional module. Failure to meet these minimum configuration requirements can cause a false power supply output fail signal. Table lists the environmental and physical specifications of the Catalyst switch chassis.
Table Catalyst Switch Specifications. Certified for operation: 0 to ft 0 to m. Designed and tested for operation: — to 10, ft —60 to m. Physical Characteristics. Dimensions H x W x D.
Note To maintain proper air circulation through the Catalyst switch chassis, we recommend that you maintain a minimum 6-inch 15 cm separation between a wall and the chassis air intake or a wall and the chassis air exhaust. You should also allow a minimum separation of 12 inches Failure to maintain adequate air space can cause the chassis to overheat and the system to fail.
On Catalyst chassis in which the airflow is from front to back, the chassis may be placed side-by-side. The Catalyst E switch is an enhanced version of the Catalyst switch. The 3-slot horizontal chassis supports redundant power supplies, redundant supervisor engines, and slots for up to two modules. It also supports a greater power capacity per slot than the Catalyst switch chassis. Table lists the features of the Catalyst E switch chassis.
Table Catalyst E Switch Features. Note Check your software release notes for specific information on module support and restrictions. Note The fan tray contains four individual fans. Table lists the environmental and physical specifications of the Catalyst E switch chassis. Table Catalyst E Switch Specifications. Humidity RH , ambient noncondensing nonoperating and storage. Designed and tested for operation: — to ft —60 to m. Physical characteristics. The Catalyst E switch is a 4-slot horizontal chassis that supports redundant power supplies, redundant supervisor engines, and slots for up to three modules.
Note The fan tray contains eight individual fans. Designed and tested for: — to 10, ft —60 to m. Operational—3 Hz to Hz. The Catalyst switch is a 6-slot horizontal chassis supporting redundant power supplies, redundant supervisor engines, and slots for up to five modules.
Figure shows a front view of the Catalyst switch chassis. Figure Catalyst Switch. Supports Supervisor Engine 1 and Supervisor Engine 2. Note You must install a W or higher capacity power supply in the chassis to power the high-speed fan tray. Note The fan trays contains six individual fans. The 6-slot horizontal chassis supports redundant power supplies, redundant supervisor engines, and slots for up to five modules.
Figure shows a front view of the Catalyst E switch. Figure Catalyst E Switch. Note You must install a W or higher capacity power supply in the chassis to power the fan tray. Note The fan tray contains six individual fans. Chassis fully configured with 1 supervisor engine, 5 switching modules, and 2 power supplies: lb Note We recommend that you maintain a minimum air space of 6 inches 16 cm between walls and the chassis air vents and a minimum horizontal separation of 12 inches The Catalyst switch is a 9-slot horizontal chassis supporting redundant power supplies, redundant supervisor engines, and slots for up to eight modules.
Note Check your software release notes for specific information on modules supported and restrictions. Note The fan tray contains nine individual fans. Chassis fully configured with 1 supervisor engine, 8 switching modules, and 2 power supplies: The 9-slot horizontal chassis supports redundant power supplies, redundant supervisor engines, and slots for up to eight modules.
Figure shows the Catalyst E switch. Note Check your software release notes for specific information on module supported and restrictions. Chassis fully configured with 1 supervisor engine, 8 switching modules, and 2 power supplies: lb The Catalyst NEB switch is a 9-slot vertical chassis supporting redundant power supplies, redundant supervisor engines, and slots for up to eight modules.
Figure shows the Catalyst NEB switch chassis. Table lists the features of the Catalyst NEB switch chassis. The kit contains a high-speed fan tray, back panel, and power harness. If you are operating the chassis from an AC source, you will also need to order a W AC-input power supply which has a front panel DC power connector.
The upgrade kit fan tray receives 42 VDC power from this front panel DC power connector through a power harness also provided in the upgrade kit. If you are operating the chassis from a DC source, you can power the system with either the W or W DC-input power supplies and power the upgrade fan tray from the site source DC.
Note Both fan tray models contain nine individual fans. Table lists the environmental and physical specifications of the Catalyst NEB switch chassis. Chassis only: 55 lb Slots Form Factor Rack Mountable. Rack Units 20 U. Layer Layer 3. Stacking No. Software None Included. Recommended Quick view Details. Cisco sku: Add to Cart. Quick view Details. Each supervisor engine must have the resources to run the switch on its own, which means all supervisor engine resources are duplicated.
The 6-slot numbered from 1 top to 6 bottom , 12 RU, horizontal chassis supports redundant power supplies and redundant supervisor engines. The Catalyst switch is a 9-slot numbered from 1 top to 9 bottom , 15 RU, horizontal chassis that supports redundant power supplies and redundant supervisor engines.
The 9-slot numbered from 1 top to 9 bottom , 15 RU, horizontal chassis supports redundant power supplies and redundant supervisor engines. The Catalyst NEB switch is a 9-slot numbered from 1 right to 9 left , 20 RU, vertical chassis that supports redundant power supplies and redundant supervisor engines.
Supervisor engine support and restrictions for the Catalyst NEB includes:. Note Refer to your software release notes for specific information on the minimum software release versions required to support the supervisor engines in the Catalyst NEBchassis.
Additional information on the Catalyst NEB switch chassis including data sheets and chassis installation is located at:. The 9-slot numbered from 1 right to 9 left , 21 RU, vertical chassis supports redundant power supplies and redundant supervisor engines. Note Refer to your software release notes for specific information on the minimum software release versions required to support the supervisor engines in the Catalyst NEB-A chassis. Additional information on the Catalyst NEB-A switch chassis including data sheets and chassis installation is located at:.
The 9-slot numbered from 1 right to 9 left , 21 RU, vertical chassis supports redundant power supplies, redundant supervisor engines, and redundant fan trays. Supervisor engine support and restrictions for the Catalyst V-E includes:. Additional information on the Catalyst V-E switch chassis including data sheets and chassis installation is located at:.
The Catalyst switch is a slot numbered from 1 top to 13 bottom , 20 RU, horizontal chassis that supports redundant power supplies and redundant supervisor engines. The Catalyst E switch is a slot numbered from 1 top to 13 bottom , 20 RU, horizontal chassis enhanced version of the Catalyst switch that supports redundant power supplies and redundant supervisor engines.
0コメント